With the recent focus in Thousand Oaks on improving fuel economy, we’ve been told how important it is to maintain our tire pressure.

Everyone in Thousand Oaks knows that tires wear out, but we all want to make them last as long as possible because they’re fairly expensive to replace. In addition to saving gas, properly inflated tires last longer. Under-inflated tires will wear out more quickly.

Some people in Thousand Oaks wonder if there is benefit to adding a few extra pounds of pressure when they fill up their tires. But actually, there isn’t. In fact, there are very good reasons not to over-inflate your tires. For one, the middle of the tread will wear unevenly because the full tread is not contacting the road properly. That also adversely affects your handling.

Come in and see us about tire maintenance for your Simi Valley, CA vehicle.
Bill’s Quality Auto Care
2016 Donville Avenue
Simi Valley, CA 93065
(805) 520-7818

Every vehicle in the Thousand Oaks area has a sticker on the driver’s side door jamb that tells you the manufacturer’s recommended tire pressure. This recommendation is an integral part of the vehicle’s suspension tuning. A lot of engineering actually goes into the recommended tire pressure, so it’s important to follow it.

What else do we need to know about tire maintenance? Tire rotation and balancing are very important. Let’s start with rotation. Because the front tires handle the brunt of turning forces, the shoulders of the front tires wear more quickly than the rear tires. We rotate the tires so that they all get to do some duty on the front and they’ll all wear evenly over their life.

For most vehicles, front tires are rotated to the rear and vice versa. Others recommend a cross rotational pattern. Some vehicles use an asymmetrical tire so those tires need to stay on either the right or left side – it’ll say which on the tire. Some high performance cars have asymmetrical tires and different sizes on the front and rear. These can’t be rotated at all. Your owner’s manual will have details for your car.

How often should you rotate your tires? Your owner’s manual will have a recommendation. Your service advisor at Bill’s Quality Auto Care can do a visual inspection to let you know if it looks like it should be done. The interval is typically around 5,000 miles.

You know, some people don’t think new tires need to be balanced. What they aren’t taking into account is the wheel. Between the wheel and the tire – even a new tire – there’s enough variation to require balancing.

When you add the valve stem and tire pressure monitoring sensors required on new cars, balancing is definitely in order. When a tire’s out of balance, it’s actually hopping down the road. You’ll feel the vibration through the steering wheel if a front tire’s out of balance and through your seat if it’s a rear tire.

Proper wheel balance promotes tire life and increases safety. Historically, lead weights have been attached to the wheel to bring it into balance. Lead gives some environmental concern, so steel weights are starting to be substituted.

Also, always use the same size tire on an axle. Different size tires on the front or on the back can lead to some real handling problems. And tire manufacturers recommend that when you get two new tires, they be installed on the rear because that’s where you need the most traction to avoid spinning-out.

Hey Moorpark, are your tires worn out? What is the standard for our CA streets? How can you tell on your SUV?

While there may be legal requirements for the Moorpark area, there are safety concerns that go beyond meeting minimum replacement mandates.

2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.

We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.

The issue is braking on wet surfaces in and around Moorpark. Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.

Picture this: you’re driving over a water covered stretch of road near Moorpark, CA. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.

Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:

• New tire tread depth
• 4/32 of an inch
• 2/32 of an inch

So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.

Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.

Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.

Of course, stopping distances were greater for the heavier pick-up truck.

How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.

How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?

For us, and we would guess for many, the answer is “no”.

Bill’s Quality Auto Care
2016 Donville Avenue
Simi Valley, CA 93065
(805) 520-7818

So, everyone in the Simi Valley CA area knows how great helium is – you know, party balloons, squeaky voices. But a lot of people around Simi Valley still haven’t heard about the benefits of nitrogen in your tires, and how it can help your tires. Here’s some great advice from AutoNetTV, brought to you by Bill’s Quality Auto Care.

Nitrogen has actually been around for a long time in the Simi Valley CA commercial sector, but it’s just starting to catch on for private vehicles in the 93065 zip code area.

Why nitrogen in your tires? Air is air, right? Actually, it turns out there is a difference.

Contact Bill’s Quality Auto Care to learn more about nitrogen in your tires
You can find us at:
2016 Donville Avenue
Simi Valley, CA 93065
Or call us at (805) 520-7818

The heart of the matter is maintaining proper tire inflation. When your tires are properly inflated, they last longer, handle better and more safely, and save you money at the gas pump.

The problem is that tires filled in Simi Valley with regular air can lose a pound and a half of air pressure every month. This just happens as the oxygen in the tire seeps out. So if you don’t check your pressure for a month or two, well, you can be significantly low – low enough to actually affect your handling, shorten tire life and waste money at the fuel pump.

How does nitrogen help? Regular air contains about 78% nitrogen. Nitrogen is the largest molecule in air. It’s dry and non-flammable. Air also contains 21% oxygen, which is smaller and seeps out of the tire three to four times faster than nitrogen.

So, a tire filled with nitrogen at Bill’s Quality Auto Care will take about six months to lose as much pressure as regular air does in just one month. So it’s more forgiving for those who don’t check their pressure every week.

Also, when oxygen is at higher temperatures – like those inside your tire when you’ve been driving for awhile – it oxidizes the inside of your tire. Getting the oxygen out of your tire means that it’ll last longer.

Who’s using nitrogen? Well, let’s start with NASCAR and Indy. These racers like nitrogen’s ability to maintain consistent tire pressure and reduce tire temperatures under very demanding conditions. The US government requires all commercial aircraft to have nitrogen in their tires. NASA and the US Military use nitrogen. The mining industry has been filling those “humongous” tires with nitrogen for years. And semi trucks and trailers are starting to use nitrogen extensively.

You may have heard some detractors of nitrogen. But the studies and white papers from tire and vehicle manufacturers demonstrate that the technology really works.

In fact, a prominent consumer research group did a study where they filled some tires with air and some with nitrogen and stacked them outside for a year. They observed that the nitrogen filled tires did hold their pressure better, but they couldn’t see the economic benefit. But that particular test has very little to do with the real world. Most tires are actually holding up cars and they also get driven around and do a lot of work. So if nitrogen helps them last longer, saves gas and gives safer handling, it’s worth considering.

Learn more about nitrogen in your tires by watching our attached auto tips video from AutoNetTV.

Let me start by saying that your wheel bearings keep the wheels on your vehicle. Did that get your attention? In this article we’ll discuss more about wheel bearings and how you can keep them doing their very important job while you drive around Simi Valley CA.

Come see us at: 2016 Donville Avenue Simi Valley, CA 93065

Wheel bearings are pretty simple parts. They’re made of high quality steel and are engineered to last 100,000 miles or more if properly cared for. The bearings do two very important jobs: First they allow the wheel to freely rotate with as little friction as possible. Second, they support the weight of the vehicle. For example, if your car weighs 3,600 pounds, each wheel has to support approximately 900 pounds. That’s a lot of heavy lifting over many, many thousands of miles.

Even though wheel bearings are relatively simple, they need to be in near perfect condition to do their job. The bearings are packed with heavy grease to lubricate and protect them. A seal keeps the grease in and water and dirt out. It’s when the seal starts to leak that problems begin. The grease can become contaminated; causing the wheel bearings to overheat and ultimately fail.

The first sign that your wheel bearings are in trouble is an unusual noise coming from a wheel. It could be a chirping, growling, rumbling or a cyclic sound. The noise could get louder or even disappear at certain speeds. Your technician at Bill’s Quality Auto Care can inspect for bearing wear by lifting the vehicle and checking for play in the wheel.

Now some wheel bearing assemblies are factory sealed. That means that they cannot be serviced – they can only be replaced. Those that aren’t sealed can be serviced on schedule. The bearings are removed, cleaned and inspected. If the bearings are still good, they’re re-installed – if not, they’re replaced. They are then packed in grease and a new seal is installed.

If your vehicle has a factory sealed wheel bearing assembly, the entire assembly needs to be replaced when trouble arises. Unfortunately, the parts are pretty pricy – but they usually last about 150,000 miles as long as the seals hold up.

Now, even a good seal cannot keep out water that’s exerting pressure on the seal. So if you’ve driven through hub deep water your bearings should be cleaned and repacked if they’re serviceable. If you have factory sealed bearings, you just need to watch for signs of premature failure.

If your wheel bearings can be serviced, your owner’s manual will recommend an interval, usually around 30,000 miles.

Now, if you have any sort of trailer, don’t forget its wheel bearings. They probably need to be serviced even more frequently. This is especially true for boat trailers that are used to launch the boat by backing it into the water. These should be serviced every year, usually at the end of the season so that the bearings don’t have the opportunity to sit and rust all winter.

So what happens if wheel bearings fail? Well, the wheel can literally fall off the vehicle. I don’t need to tell you how bad that could be. So check with your service advisor at Bill’s Quality Auto Care and see if your vehicle’s wheel bearings can be serviced and when it’s recommended. Listen for warning signs. If you’ve been fording streams or puddle surfing after rainstorms, be especially vigilant.

Come by Bill’s Quality Auto Care for a wheel bearing inspection, or for Oil Change Service. Call for an appointment at (805) 520-7818

Everyone in the Moorpark area wants our tires to last as long as possible. Two ways to maximize tire life are wheel balancing and tire rotation.

When wheels are out of balance, they wobble a bit. That makes the tires wear in a cupping pattern. And they vibrate. To fix this, your service technician at Bill’s Quality Auto Care puts weights on your wheels to balance them out. If a front wheel is out of balance you’ll feel it in the steering wheel. If it’s a rear wheel you’ll feel it through your seat.

That brings us to tire rotation. The front tires on a car wear out more quickly than the rear tires. As they push through turns from Simi Valley to Thousand Oaks, the shoulders of the front tires wear down. So rotating front and rear tires allows them to all wear at about the same rate over the life of the tire.

Proper tire inflation will also help your tires last longer. Under-inflated tires wear excessively on the shoulder and may even overheat. This could cause tire damage or a blow out. Over-inflated tires wear to fast in the middle.

Four wheel drive trucks and SUV’s tend to wear their tires more unevenly so rotation is even more important with them. Give us a call to get our recommendation on your SUV.

See your owner’s manual or ask your service technician at Bill’s Quality Auto Care for your recommended tire rotation schedule. It’s usually every 5,000 to 8,000 miles.

Tires cost a lot and they are one of the most critical safety components on your vehicle. Take care of them and they’ll take care of you.

Bill’s Quality Auto Care
2016 Donville Avenue
Simi Valley, CA 93065
(805) 520-7818